Numerical Investigation of the Effect of Artificial Roughness on the Flow Field and Heat Transfer Rate in a Rectangular Channel

Authors

  • Hamed Mohaddes Deylami * Department of Mechanical Engineering, University of Guilan, Rasht, Iran. https://orcid.org/0000-0003-1125-2134
  • Soheila Sojodi Department of Mechanical Engineering, University of Guilan, Rasht, Iran.

https://doi.org/10.48313/mtei.v3i2.83

Abstract

In the current study, the numerical analysis of the turbulent flow field and heat transfer in a flat rectangular channel having roughness elements on its bottom surface is conducted. Two dimensional, steady, incompressible and turbulent flow simulations are carried out using the Finite Volume Method (FVM). In this regard, the structured non-uniform quadrilateral mesh is chosen, where the pressure term is discretized using the standard scheme while all other governing equations are discretized by using second order upwind scheme. The SIMPLE scheme is used for coupling the pressure velocity field. The effect of important parameters such as Reynolds number (5400 < Re < 23000), ratio of roughness height to channel height (0.06 < e/H < 0.26) and ratio of roughness thickness to pitch (0.25 < t/P < 1.0) on average Nusselt number, friction factor and thermal performance improvement factor has been investigated. It is found that increase in Reynolds number increases the heat transfer rate but decreases the thermal performance factor. Moreover, increase in ratio of thickness to pitch and decrease in ratio of height to channel improves the thermal performance. The RNG k ε turbulence model shows better prediction compared to the experimental data.     

Keywords:

Artificial roughness, Heat transfer enhancement, Numerical investigation, Rectangular channel, Turbulent flow, RNG k ε model, Thermal performance factor

References

  1. [1] Bergles, A. E. (2002). ExHFT for fourth generation heat transfer technology. Experimental thermal and fluid science, 26(2), 335–344. https://doi.org/10.1016/S0894-1777(02)00145-0
  2. [2] Webb, R. L., & Kim, N. H. (2004). Principles enhanced heat trans. Garland Science. https://doi.org/10.1201/b12413
  3. [3] Zhou, F., & Catton, I. (2013). A numerical investigation of turbulent flow and heat transfer in rectangular channels with elliptic scale-roughened walls. Journal of heat transfer, 135(8), 81901. https://doi.org/10.1115/1.4024278
  4. [4] Singh, I., & Singh, S. (2018). A review of artificial roughness geometries employed in solar air heaters. Renewable and sustainable energy reviews, 92, 405–425. https://doi.org/10.1016/j.rser.2018.04.108
  5. [5] Burns, J. C., & Parkes, T. (1967). Peristaltic motion. Journal of fluid mechanics, 29(4), 731–743. 10.1017/S0022112067001156
  6. [6] Goldstein Leonardo, J., & Sparrow, E. M. (1977). Heat/Mass transfer characteristics for flow in a corrugated wall channel. Journal of heat transfer, 99(2), 187–195. https://doi.org/10.1115/1.3450667
  7. [7] O’Brien, J. E., & Sparrow, E. M. (1982). Corrugated-duct heat transfer, pressure drop, and flow visualization. Journal of heat transfer, 104(3), 410–416. https://doi.org/10.1115/1.3245108
  8. [8] Saniei, N., & Dini, S. (1993). Heat Transfer Characteristics in a Wavy-Walled Channel. Journal of heat transfer, 115(3), 788–792. https://doi.org/10.1115/1.2910756
  9. [9] Wang, G., & Vanka, S. P. (1995). Convective heat transfer in periodic wavy passages. International journal of heat and mass transfer, 38(17), 3219–3230. https://doi.org/10.1016/0017-9310(95)00051-A
  10. [10] Patel, V. C., Chon, J. T., & Yoon, J. Y. (1991). Turbulent flow in a channel with a wavy wall. Journal of fluids engineering, 113(4), 579–586. https://doi.org/10.1115/1.2926518
  11. [11] Gloerfelt, X., & Cinnella, P. (2019). Large eddy simulation requirements for the flow over periodic hills. Flow, turbulence and combustion, 103(1), 55–91. https://doi.org/10.1007/s10494-018-0005-5
  12. [12] Ziefle, J., Stolz, S., & Kleiser, L. (2008). Large-eddy simulation of separated flow in a channel with streamwise-periodic constrictions. AIAA journal, 46(7), 1705–1718. https://doi.org/10.2514/1.33891
  13. [13] Yang, L. C., Asako, Y., Yamaguchi, Y., & Faghri, M. (1997). Numerical prediction of transitional characteristics of flow and heat transfer in a corrugated duct. Journal of heat transfer, 119(1), 62–69. https://doi.org/10.1115/1.2824101
  14. [14] Amano, R. S. (1985). A numerical study of laminar and turbulent heat transfer in a periodically corrugated wall channel. Journal of heat transfer, 107(3), 564–569. https://doi.org/10.1115/1.3247461
  15. [15] Islamoglu, Y., & Parmaksizoglu, C. (2003). The effect of channel height on the enhanced heat transfer characteristics in a corrugated heat exchanger channel. Applied thermal engineering, 23(8), 979–987. https://doi.org/10.1016/S1359-4311(03)00029-2
  16. [16] Islamoglu, Y., & Parmaksizoglu, C. (2004). Numerical investigation of convective heat transfer and pressure drop in a corrugated heat exchanger channel. Applied thermal engineering, 24(1), 141–147. https://doi.org/10.1016/j.applthermaleng.2003.07.004
  17. [17] Naphon, P. (2007). Heat transfer characteristics and pressure drop in channel with V corrugated upper and lower plates. Energy conversion and management, 48(5), 1516–1524. https://doi.org/10.1016/j.enconman.2006.11.020
  18. [18] Naphon, P., & Kornkumjayrit, K. (2008). Numerical analysis on the fluid flow and heat transfer in the channel with V-shaped wavy lower plate. International communications in heat and mass transfer, 35(7), 839–843. https://doi.org/10.1016/j.icheatmasstransfer.2008.03.010
  19. [19] Naphon, P. (2008). Effect of corrugated plates in an in-phase arrangement on the heat transfer and flow developments. International journal of heat and mass transfer, 51(15), 3963–3971. https://doi.org/10.1016/j.ijheatmasstransfer.2007.11.050
  20. [20] Eiamsa-ard, S., & Promvonge, P. (2008). Numerical study on heat transfer of turbulent channel flow over periodic grooves. International communications in heat and mass transfer, 35(7), 844–852. https://doi.org/10.1016/j.icheatmasstransfer.2008.03.008
  21. [21] Thianpong, C., Chompookham, T., Skullong, S., & Promvonge, P. (2009). Thermal characterization of turbulent flow in a channel with isosceles triangular ribs. International communications in heat and mass transfer, 36(7), 712–717. https://doi.org/10.1016/j.icheatmasstransfer.2009.03.027
  22. [22] Elshafei, E. A. M., Awad, M. M., El-Negiry, E., & Ali, A. G. (2010). Heat transfer and pressure drop in corrugated channels. Energy, 35(1), 101–110. https://doi.org/10.1016/j.energy.2009.08.031
  23. [23] Yin, J., Yang, G., & Li, Y. (2012). The effects of wavy plate phase shift on flow and heat transfer characteristics in corrugated channel. Energy procedia, 14, 1566–1573. https://doi.org/10.1016/j.egypro.2011.12.1134
  24. [24] Tanda, G. (2011). Effect of rib spacing on heat transfer and friction in a rectangular channel with 45° angled rib turbulators on one/two walls. International journal of heat and mass transfer, 54(5), 1081–1090. https://doi.org/10.1016/j.ijheatmasstransfer.2010.11.015
  25. [25] Ramgadia, A. G., & Saha, A. K. (2012). Fully developed flow and heat transfer characteristics in a wavy passage: Effect of amplitude of waviness and Reynolds number. International journal of heat and mass transfer, 55(9), 2494–2509. https://doi.org/10.1016/j.ijheatmasstransfer.2012.01.010
  26. [26] Desrues, T., Marty, P., & Fourmigué, J. F. (2012). Numerical prediction of heat transfer and pressure drop in three-dimensional channels with alternated opposed ribs. Applied thermal engineering, 45–46, 52–63. https://doi.org/10.1016/j.applthermaleng.2012.03.013
  27. [27] Mohammed, H. A., Abed, A. M., & Wahid, M. A. (2013). The effects of geometrical parameters of a corrugated channel with in out-of-phase arrangement. International communications in heat and mass transfer, 40, 47–57. https://doi.org/10.1016/j.icheatmasstransfer.2012.10.022
  28. [28] Ravi, B. V., Singh, P., & Ekkad, S. V. (2017). Numerical investigation of turbulent flow and heat transfer in two-pass ribbed channels. International journal of thermal sciences, 112, 31–43. https://doi.org/10.1016/j.ijthermalsci.2016.09.034
  29. [29] Versteeg, H. K., & Malalasekera, W. (2007). An introduction to computational fluid dynamics: The finite volume method. Pearson Education Limited. https://books.google.com/books/about/An_Introduction_to_Computational_Fluid_D.html?id=RvBZ-UMpGzIC
  30. [30] Launder, B. E., & Spalding, D. B. (1983). Paper 8 - The numerical computation of turbulent flows. In Numerical prediction of flow, heat transfer, turbulence and combustion (pp. 96–116). Pergamon. https://doi.org/10.1016/B978-0-08-030937-8.50016-7

Downloads

Published

2026-06-10

Issue

Vol. 3 No. 2 (2026): Mechanical Technology and Engineering Insights (MTEI)

Section

Articles

How to Cite

Mohaddes Deylami, H. ., & Sojodi, S. . (2026). Numerical Investigation of the Effect of Artificial Roughness on the Flow Field and Heat Transfer Rate in a Rectangular Channel. Mechanical Technology and Engineering Insights, 3(2), 101-117. https://doi.org/10.48313/mtei.v3i2.83

Similar Articles

1-10 of 48

You may also start an advanced similarity search for this article.